Have you been thinking of adding a welder to your arsenal of tools to the ultimate preparedness?

The Ready Welder is a self contained and complete unit. Simply disconnect your battery terminals, get a second battery, connect them in series and you are ready to weld up to 1/2" plate steel. There is no need to hardwire and permanentyly bolt the welder to your truck, and there is no need to buy a new expensive alternator to support the welder. This is an excellent tool for home or portable use. Welds steel, stainless steel and aluminum.

Warning: must not be connected to vehicle battery when hooked up to the vehicle. Serious damage will occur in the electrical system.

Additional info on Pirate 4x4

Nicole Johnson Special 10000-ADP-CS

Nicole Johnson Model 10000ADP-CS Features:

• Welds Steel, Stainless and Aluminum
• Connects to Batteries
  – 18 Volt Battery will Weld up to 3/16"
  – 24 Volt will Single Pass 1/2" @ 250 amps
  – 36 Volt will Weld up to 3/4" @ up to 350 amps
• Welds 22 Gage to 3/4"
• Connects to MIG/Constant Voltage Output Welders
• Uses Wire Sizes from .023 to .040 without changing rollers.
• Uses Heavy-Duty TWECO Quality Front End Consumables
• Wire Speeds of 50 Inches to 900 Inches per Minute
• Polarity Indicator Lights
• Ten Foot Cable with Quick Disconnects, can be extended to 80 Feet
• Built-in Gas Valve
• Ground Cable Attached
• Built In Cold Switch
• Built In Cold Switch

Special Edition Contents:

*Custom Retail Packaging & Spoolgun Graphic
*Nicole Johnson Signature Decal
*Special Edition Tee Shirt
*Identifying Spoolgun Graphic

Discount Vouchers from:

*Viking Offroad - Winchline.com Recovery Gear
*Ride PRP Seats
*4x4 Oil, Your Source for Amsoil Lubricants
*Turn Key Engine Supply
*Kicker Performance Audio
*BFGoodrich Tires

$749

Model 10000

The RWII Model #10000 is cabled best for battery operation. This model will also connect to all CV (constant voltage) and DC (direct current) output machines. This model is most frequently used by 4X4 off-road enthusiasts primarily using batteries as the power source.

The ground cable is attached to the red dual quick disconnect connectors. This makes welding jobs in remote locations easy, portable and quick. This model will run off any 18, 24 & 36 volt batteries in a parallel series depending on the application and material to be welded. The Model #10000 has a one year 100% parts and labor limited factory warranty.

Model 10000 Features:

• Welds Steel, Stainless and Aluminum
• Connects to Batteries
  – 18 Volt Battery can do Thin Sheet Metal
  – 24 Volt will Single Pass 1/2" @275 amp
  – 36 Volt will Weld up to 3/4" @350 to 400 amp
• Welds 22 Gage to 3/4"
• Connects to MIG/Constant Voltage Output Welders
• Uses Wire Sizes from .023 to .045 without changing rollers.
• Uses Heavy-Duty TWECO Quality Front End Consumables
• Wire Speeds of 50 Inches to 900 Inches per Minute
• Polarity Indicator Lights
• Ten Foot Cable with Quick Disconnects, Can be
• Extended to 100 Feet
• Built-in Gas Valve
  
• Ground Cable Attached

Ready Welder II Case Includes:

*RWII High-Impact MIG Gun
*Ten Feet of Cable
*One Spool of Flux Core Wire
*300 Amp Ground Clamp
*Two Battery Clamps
*Extra Tips and Gas Hose Fitting
*Ten Extra Feet of Gas Hose
*Foam Lined Blow-Molded Tough Briefcase

$569

Model 10000 ADP

The RWII Model #10000ADP is cabled for battery operation and with the addition of the AC to DC Power Converter the Model 10000ADP will also connect to CC (constant current) stick machines as well as CV (constant voltage) machines. The Model ADP is most frequently bought and used by the maintenance facilities/public works, construction companies, industrial companies, as well as, repairmen, maintenance workers, 4X4 off-road enthusiasts, ranchers, boaters and the agricultural industry. Since there are more Stick welding machines in the market place than any other welder, the Model ADP would be the perfect buy for those want the ability to connect to all DC out put welding machines. The Model #10000ADP has a one year 100% parts and labor limited factory warranty.

Model 10000ADP Features:

• Welds Steel, Stainless and Aluminum
• Connects to Batteries
  – 18 Volt Battery can do Thin Sheet Metal
  – 24 Volt will Single Pass 1/2" @275 amp
  – 36 Volt will Weld up to 3/4" @350 to 400 amp
• Welds 22 Gage to 3/4"
• Connects to MIG/Constant Voltage Output Welders
• Uses Wire Sizes from .023 to .045 without Changing Rollers
• Uses Heavy-Duty TWECO Quality Front End Consumables
• Wire Speeds of 50 Inches to 900 Inches per Minute
• Polarity Indicator Lights
• Ten Foot Cable with Quick Disconnects, Can be
• Extended to 100 Feet
• Built-in Gas Valve
• Ground Cable Attached

$589

• Welds Steel, Stainless and Aluminum
• Connects to Batteries
  – 18 Volt Battery can do Thin Sheet Metal
  – 24 Volt will Single Pass 1/2" @275 amp
  – 36 Volt will Weld up to 3/4" @350 to 400 amp
• Welds 22 Gage to 3/4"
• Connects to MIG/Constant Voltage Output Welders
• Uses Wire Sizes from .023 to .045 without Changing Rollers
• Uses Heavy-Duty TWECO Quality Front End Consumables
• Wire Speeds of 50 Inches to 900 Inches per Minute
• Polarity Indicator Lights
• Ten Foot Cable with Quick Disconnects, Can be
• Extended to 100 Feet
• Built-in Gas Valve
• Ground Cable Attached
• Built In Cold Switch

$689

Since the introduction , in 1997, of the Ready Welder as the first battery powered portable welder, there have been other battery powered welders brought out in the market. None of these have had all of the desirable qualities of Ready Welder II. As a result, the U.S. Army is, and has been one of Ready Welder's most important customers. (see Military Testimonials) IMPAC credit cards honored. NSN # 5130-01-522-1379 Military Pack. Tel 1-800 935 3644

Ready Welder is a compact battery powered MIG welder. It operates on two or three 12 volt DC batteries in series, producing 200 to 350 Amps of power for deep penetration of metals. For thinner metals a 12 and a 6 volt battery connected in series to produce 18 DC volts and lower Amps works just fine. The use of a single 12 volt battery is not normally recommended..

The Professionals who use it, report that the Ready Welder is a high yielding asset in their welding trade, because of it's lower initial cost plus it's lower operating costs. A smaller truck can be used to go out for field repairs with the Ready Welder. The setup time and electrical usage costs are less than before they began using this Product.

The Ready Welder can also be used as a Spool Gun, by connecting it to a Stick Welder or a conventional MIG machine. It operates from 115 AC volts while plugged into any welding device which might require a Spool Gun, for example, as when welding aluminum.

Our Model 10000 is the original Ready Welder II, introduced in 1997. Since then, we have developed several new Models, and each has all of the same basic functions as Model 10000. The latest of the new Models, introduced in early 2004 is the -CS model variations. The Cold Switch Models have added a safety feature of trigger release cutoff from live power to the unit, when not welding.

Before you buy or even think of acquiring a MIG welder, we suggest that you click Testimonials and Military Testimonials to see what users of Ready Welder think of the product after buying one and using it. Then check the Comparison Charts, to learn what Ready Welder can do, and how it rates versus other MIG welders.

Every customer is treated individually by a trained staff member who is dedicated to satisfying the customer. We take pride in our service, in sharing our expertise with them, and in our one year limited warranty.

Model #10000MVP-CS, known as the "Maintenance Vehicle Pack", is specially designed for Maintenance Trucks or the Mobile Repair Vehicle. Every maintenance truck should carry one.